Ningbo Sunny Electrical Heating Appliances Co.,Ltd

Telephone:

+86-574-23678117

E-mail:

sana@sunnyheater.com

News Detail
Home > News > Content

Safety Measures For The Use Of Aluminum Diecast Heater

Safety measures for the use of Aluminum Diecast Heater
Aluminum Diecast Heater is working, living in the use of a more equipment, such as electric stove, electric iron, iron, electric heater, electric oven, etc. are electric heating equipment. Aluminum Diecast Heater resistance wire is made of nickel, chromium alloy, the temperature up to 800 ℃ or more. As the Aluminum Diecast Heater power is relatively large, users ignore the safety, the fire may occur at any time. Aluminum Diecast Heater fire causes: First, the power of Aluminum Diecast Heater on the combustible or on the vicinity of flammable materials, in a long period of high temperature baking caused a fire. Second, Aluminum Diecast Heater is not installed plug, directly into the socket head, and thus easy to cause a short circuit and a fire. Third, the use of Aluminum Diecast Heater in the Aluminum Diecast Heater is not removed when the plug unplugged for too long, resulting in Aluminum Diecast Heater overheating, ignited the adjacent fuel caused by fire. Fourth, the resistance wire after repeated repair to continue to use, can cause the line overload and cause a fire.
Therefore, in use, can not be flammable and explosive objects placed in the vicinity of Aluminum Diecast Heater, must maintain a certain safe distance. Aluminum Diecast Heater must be placed on non-thermally conductive non-combustible material base; Aluminum Diecast Heater wire safety cut-off capacity must meet the Aluminum Diecast Heater capacity requirements, industrial Aluminum Diecast Heater in any case should be installed separately Circuit. Wire must be installed plug, Aluminum Diecast Heater can not be directly inserted into the socket; Aluminum Diecast Heater wire damage should be replaced immediately, the circuit is not installed in the fuse of the Aluminum Diecast Heater shall not be used; Aluminum Diecast Heater must be used , Should be pulled out when the plug, in the course of the use, if the power failure, it should be timely Aluminum Diecast Heater plug pull out, do not forget. For multiple repair of the resistance wire, it is best not to use, should replace the new resistance wire. Flammable and explosive materials are strictly prohibited with Aluminum Diecast Heater drying; electric oven should have a temperature control device, it is necessary to prevent the temperature is too high, but also to prevent the Aluminum Diecast Heater baking time is too long.
  Aluminum Diecast Heater insulation down for a variety of reasons, the following simple analysis of several cases. Some customers buy Aluminum Diecast Heater is not immediately used, but put a long time before use. Due to improper disposal, such as Aluminum Diecast Heater place more humid, a long time will cause moisture into the heating tube, resulting in Aluminum Diecast Heater overall insulation decline. The quickest way to do this is to put the heating die of the Aluminum Diecast Heater into the oven and use the high temperature to dry the moisture and use it normally. If you do not have the case of an oven, you can also use hot air from the Aluminum Diecast Heater inlet blowing, export out, a long time, you can also discharge the tide. There is also a way, that is, directly with the fan against the Aluminum Diecast Heater inlet and outlet hair, and then open the Aluminum Diecast Heater, the use of heat pipe heat to heat the tube out of the tank.
       Of course, if the insulation is very low, it is recommended to consult the manufacturers, and then make a specific program.
       If it is not for the above reasons, some are due to the small sand of the tube for a long time there will be liquid into the insulation lead to decline, you can not use the above method, Aluminum Diecast Heater must be sent back to the factory for tube. And then can be used.